222 lines
7.0 KiB
C
222 lines
7.0 KiB
C
|
/*
|
||
|
|
ChibiOS - Copyright (C) 2006..2018 Giovanni Di Sirio
|
||
|
|
|
||
|
|
Licensed under the Apache License, Version 2.0 (the "License");
|
||
|
|
you may not use this file except in compliance with the License.
|
||
|
|
You may obtain a copy of the License at
|
||
|
|
|
||
|
|
http://www.apache.org/licenses/LICENSE-2.0
|
||
|
|
|
||
|
|
Unless required by applicable law or agreed to in writing, software
|
||
|
|
distributed under the License is distributed on an "AS IS" BASIS,
|
||
|
|
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
||
|
|
See the License for the specific language governing permissions and
|
||
|
|
limitations under the License.
|
||
|
|
*/
|
||
|
|
|
||
|
|
/*
|
||
|
|
Concepts and parts of this file have been contributed by Rocco Marco
|
||
|
|
Guglielmi.
|
||
|
|
*/
|
||
|
|
#ifndef _BOARD_H_
|
||
|
|
#define _BOARD_H_
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Setup for the ST7580 Evaluation kit board.
|
||
|
|
*/
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Board identifier.
|
||
|
|
*/
|
||
|
|
#define BOARD_ST_EVALKIT_ST7580_1
|
||
|
|
#define BOARD_NAME "STMicroelectronics EVALKITST7580_1"
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Board frequencies.
|
||
|
|
*/
|
||
|
|
#define STM32_LSECLK 0
|
||
|
|
#define STM32_HSECLK 8000000
|
||
|
|
|
||
|
|
/*
|
||
|
|
* MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h.
|
||
|
|
*/
|
||
|
|
#define STM32F103xB
|
||
|
|
|
||
|
|
/*
|
||
|
|
* IO pins assignments.
|
||
|
|
*/
|
||
|
|
#define GPIOA_CL_ADC 0
|
||
|
|
#define GPIOA_PLC_T_REQ 1
|
||
|
|
#define GPIOA_PLC_TXD 2
|
||
|
|
#define GPIOA_PLC_RXD 3
|
||
|
|
#define GPIOA_SD_NSS 4
|
||
|
|
#define GPIOA_SD_SCLK 5
|
||
|
|
#define GPIOA_SD_MISO 6
|
||
|
|
#define GPIOA_SD_MOSI 7
|
||
|
|
#define GPIOA_8MHZ_MCO 8
|
||
|
|
#define GPIOA_UART1_TXD 9
|
||
|
|
#define GPIOA_UART1_RXD 10
|
||
|
|
#define GPIOA_USBDM 11
|
||
|
|
#define GPIOA_USBDP 12
|
||
|
|
#define GPIOA_JTMS 13
|
||
|
|
#define GPIOA_JTCK 14
|
||
|
|
#define GPIOA_JTDI 15
|
||
|
|
|
||
|
|
#define GPIOB_SD_CD 0
|
||
|
|
#define GPIOB_PA_ADC 1
|
||
|
|
#define GPIOB_BOOT1 2
|
||
|
|
#define GPIOB_J_TDO 3
|
||
|
|
#define GPIOB_J_TRSTN 4
|
||
|
|
#define GPIOB_LED_RED 5
|
||
|
|
#define GPIOB_LED_YELLOW 6
|
||
|
|
#define GPIOB_LED_GREEN 7
|
||
|
|
#define GPIOB_I2C1_SCL 8
|
||
|
|
#define GPIOB_I2C1_SDA 9
|
||
|
|
#define GPIOB_SW4 10
|
||
|
|
#define GPIOB_SW3 11
|
||
|
|
#define GPIOB_DIP_SW4 12
|
||
|
|
#define GPIOB_DIP_SW3 13
|
||
|
|
#define GPIOB_DIP_SW2 14
|
||
|
|
#define GPIOB_DIP_SW1 15
|
||
|
|
|
||
|
|
#define GPIOC_PC0 0
|
||
|
|
#define GPIOC_PC1 1
|
||
|
|
#define GPIOC_PC2 2
|
||
|
|
#define GPIOC_PC3 3
|
||
|
|
#define GPIOC_PC4 4
|
||
|
|
#define GPIOC_PC5 5
|
||
|
|
#define GPIOC_PC6 6
|
||
|
|
#define GPIOC_PC7 7
|
||
|
|
#define GPIOC_PC8 8
|
||
|
|
#define GPIOC_PC9 9
|
||
|
|
#define GPIOC_PC10 10
|
||
|
|
#define GPIOC_PC11 11
|
||
|
|
#define GPIOC_PC12 12
|
||
|
|
#define GPIOC_PL_RX_ON 13
|
||
|
|
#define GPIOC_PL_TX_ON 14
|
||
|
|
#define GPIOC_PLC_RESETN 15
|
||
|
|
|
||
|
|
#define GPIOD_OSC_IN 0
|
||
|
|
#define GPIOD_OSC_OUT 1
|
||
|
|
|
||
|
|
/*
|
||
|
|
* I/O ports initial setup, this configuration is established soon after reset
|
||
|
|
* in the initialization code.
|
||
|
|
*
|
||
|
|
* The digits have the following meaning:
|
||
|
|
* 0 - Analog input.
|
||
|
|
* 1 - Push Pull output 10MHz.
|
||
|
|
* 2 - Push Pull output 2MHz.
|
||
|
|
* 3 - Push Pull output 50MHz.
|
||
|
|
* 4 - Digital input.
|
||
|
|
* 5 - Open Drain output 10MHz.
|
||
|
|
* 6 - Open Drain output 2MHz.
|
||
|
|
* 7 - Open Drain output 50MHz.
|
||
|
|
* 8 - Digital input with PullUp or PullDown resistor depending on ODR.
|
||
|
|
* 9 - Alternate Push Pull output 10MHz.
|
||
|
|
* A - Alternate Push Pull output 2MHz.
|
||
|
|
* B - Alternate Push Pull output 50MHz.
|
||
|
|
* C - Reserved.
|
||
|
|
* D - Alternate Open Drain output 10MHz.
|
||
|
|
* E - Alternate Open Drain output 2MHz.
|
||
|
|
* F - Alternate Open Drain output 50MHz.
|
||
|
|
* Please refer to the STM32 Reference Manual for details.
|
||
|
|
*/
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Port A setup.
|
||
|
|
* PA0 - Analog input (GPIOA_CL_ADC)
|
||
|
|
* PA1 - Push Pull output (GPIOA_PLC_T_REQ).
|
||
|
|
* PA2 - Alternate output (GPIOA_PLC_TXD).
|
||
|
|
* PA3 - Pull-up input (GPIOA_PLC_RXD).
|
||
|
|
* PA4 - Push Pull output (GPIOA_SD_NSS).
|
||
|
|
* PA5 - Alternate output (GPIOA_SD_SCLK).
|
||
|
|
* PA6 - Alternate output (GPIOA_SD_MISO).
|
||
|
|
* PA7 - Alternate output (GPIOA_SD_MOSI).
|
||
|
|
* PA8 - Alternate output (GPIOA_8MHZ_MCO).
|
||
|
|
* PA9 - Alternate output (GPIOA_UART1_TXD).
|
||
|
|
* PA10 - Normal input (GPIOA_UART1_RXD).
|
||
|
|
* PA11 - Alternate output (GPIOA_USBDM).
|
||
|
|
* PA12 - Alternate output (GPIOA_USBDP).
|
||
|
|
* PA13 - Pull-up input (GPIOA_JTMS).
|
||
|
|
* PA14 - Pull-down input (GPIOA_JTCK).
|
||
|
|
* PA15 - Pull-up input (GPIOA_JTDI).
|
||
|
|
*/
|
||
|
|
#define VAL_GPIOACRL 0xBBB38B30 /* PA7...PA0 */
|
||
|
|
#define VAL_GPIOACRH 0x888BB4BB /* PA15...PA8 */
|
||
|
|
#define VAL_GPIOAODR 0xFFFFBFFF
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Port B setup.
|
||
|
|
* PB0 - Pull-up input (GPIOB_SD_CD)
|
||
|
|
* PB1 - Analog input (GPIOB_PA_ADC).
|
||
|
|
* PB2 - Normal input (GPIOB_BOOT1).
|
||
|
|
* PB3 - Pull-up input (GPIOB_J_TDO).
|
||
|
|
* PB4 - Pull-up input (GPIOB_J_TRSTN).
|
||
|
|
* PB5 - Push Pull output (GPIOB_LED_RED).
|
||
|
|
* PB6 - Push Pull output (GPIOB_LED_YELLOW).
|
||
|
|
* PB7 - Push Pull output (GPIOB_LED_GREEN).
|
||
|
|
* PB8 - Alternate output (GPIOB_I2C1_SCL).
|
||
|
|
* PB9 - Alternate output (GPIOB_I2C1_SDA).
|
||
|
|
* PB10 - Normal input (GPIOB_SW4).
|
||
|
|
* PB11 - Normal input (GPIOB_SW3).
|
||
|
|
* PB12 - Normal input (GPIOB_DIP_SW4).
|
||
|
|
* PB13 - Normal input (GPIOB_DIP_SW3).
|
||
|
|
* PB14 - Normal input (GPIOB_DIP_SW2).
|
||
|
|
* PB15 - Normal input (GPIOB_DIP_SW1).
|
||
|
|
*/
|
||
|
|
#define VAL_GPIOBCRL 0x33388408 /* PB7...PB0 */
|
||
|
|
#define VAL_GPIOBCRH 0x444444BB /* PB15...PB8 */
|
||
|
|
#define VAL_GPIOBODR 0xFFFFFFFF
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Port C setup.
|
||
|
|
* Everything input with pull-up except:
|
||
|
|
* PC13 - Normal input (GPIOC_PL_RX_ON).
|
||
|
|
* PC14 - Normal input (GPIOC_PL_TX_ON).
|
||
|
|
* PC15 - Push Pull output (GPIOC_PLC_RESETN).
|
||
|
|
*/
|
||
|
|
#define VAL_GPIOCCRL 0x88888888 /* PC7...PC0 */
|
||
|
|
#define VAL_GPIOCCRH 0x34488888 /* PC15...PC8 */
|
||
|
|
#define VAL_GPIOCODR 0xFFFFFFFF
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Port D setup.
|
||
|
|
* Everything input with pull-up except:
|
||
|
|
* PD0 - Normal input (GPIOD_OSC_IN).
|
||
|
|
* PD1 - Normal input (GPIOD_OSC_OUT).
|
||
|
|
*/
|
||
|
|
#define VAL_GPIODCRL 0x88888844 /* PD7...PD0 */
|
||
|
|
#define VAL_GPIODCRH 0x88888888 /* PD15...PD8 */
|
||
|
|
#define VAL_GPIODODR 0xFFFFFFFF
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Port E setup.
|
||
|
|
* Everything input with pull-up except:
|
||
|
|
*/
|
||
|
|
#define VAL_GPIOECRL 0x88888888 /* PE7...PE0 */
|
||
|
|
#define VAL_GPIOECRH 0x88888888 /* PE15...PE8 */
|
||
|
|
#define VAL_GPIOEODR 0xFFFFFFFF
|
||
|
|
|
||
|
|
/*
|
||
|
|
* USB bus activation macro, required by the USB driver.
|
||
|
|
*/
|
||
|
|
#define usb_lld_connect_bus(usbp)
|
||
|
|
|
||
|
|
/*
|
||
|
|
* USB bus de-activation macro, required by the USB driver.
|
||
|
|
*/
|
||
|
|
#define usb_lld_disconnect_bus(usbp)
|
||
|
|
|
||
|
|
#if !defined(_FROM_ASM_)
|
||
|
|
#ifdef __cplusplus
|
||
|
|
extern "C" {
|
||
|
|
#endif
|
||
|
|
void boardInit(void);
|
||
|
|
#ifdef __cplusplus
|
||
|
|
}
|
||
|
|
#endif
|
||
|
|
#endif /* _FROM_ASM_ */
|
||
|
|
|
||
|
|
#endif /* _BOARD_H_ */
|