90 lines
2.5 KiB
C
90 lines
2.5 KiB
C
/*
|
|
ChibiOS - Copyright (C) 2016 flabbergast <s3+flabbergast@sdfeu.org>
|
|
|
|
Licensed under the Apache License, Version 2.0 (the "License");
|
|
you may not use this file except in compliance with the License.
|
|
You may obtain a copy of the License at
|
|
|
|
http://www.apache.org/licenses/LICENSE-2.0
|
|
|
|
Unless required by applicable law or agreed to in writing, software
|
|
distributed under the License is distributed on an "AS IS" BASIS,
|
|
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
See the License for the specific language governing permissions and
|
|
limitations under the License.
|
|
*/
|
|
|
|
#ifndef _BOARD_H_
|
|
#define _BOARD_H_
|
|
|
|
/*
|
|
* Setup for Freescale Freedom KL26Z board.
|
|
*/
|
|
|
|
/*
|
|
* Board identifier.
|
|
*/
|
|
#define BOARD_FREESCALE_FREEDOM_KL26Z
|
|
#define BOARD_NAME "Freescale Freedom KL26Z"
|
|
|
|
/* External 8 MHz crystal. */
|
|
#define KINETIS_XTAL_FREQUENCY 8000000UL
|
|
|
|
/*
|
|
* MCU type
|
|
*/
|
|
#define KL26
|
|
|
|
/*
|
|
* Onboard features.
|
|
*/
|
|
#define GPIO_LED_RED IOPORT5
|
|
#define PIN_LED_RED 29
|
|
#define GPIO_LED_GREEN IOPORT5
|
|
#define PIN_LED_GREEN 31
|
|
#define GPIO_LED_BLUE IOPORT4
|
|
#define PIN_LED_BLUE 5
|
|
#define GPIO_BUTTON IOPORT4
|
|
#define PIN_BUTTON 0
|
|
#define GPIO_LIGHT_SENSOR IOPORT5
|
|
#define PIN_LIGHT_SENSOR 22
|
|
|
|
/* Inertial sensor: FXOS8700CQ */
|
|
/* Default I2C address 0x1D */
|
|
/* Note: the pins PTE24/25 are assigned to I2C0 by default;
|
|
* if I2C0 is wanted on other pins, these need to be
|
|
* assigned another function explicitly!
|
|
*/
|
|
#define I2C_GYRO I2C0
|
|
|
|
#define LINE_LED_RED PAL_LINE(GPIO_LED_RED, PIN_LED_RED)
|
|
#define LINE_LED_GREEN PAL_LINE(GPIO_LED_GREEN, PIN_LED_GREEN)
|
|
#define LINE_LED_BLUE PAL_LINE(GPIO_LED_BLUE, PIN_LED_BLUE)
|
|
#define LINE_BUTTON PAL_LINE(GPIO_BUTTON, PIN_BUTTON)
|
|
#define LINE_LIGHT_SENSOR PAL_LINE(GPIO_LIGHT_SENSOR, PIN_LIGHT_SENSOR)
|
|
#define LINE_GYRO_SCL PAL_LINE(GPIOE, 24U)
|
|
#define LINE_GYRO_SDA PAL_LINE(GPIOE, 25U)
|
|
#define LINE_GYRO_INT1 PAL_LINE(GPIOD, 0U)
|
|
#define LINE_GYRO_INT2 PAL_LINE(GPIOD, 1U)
|
|
|
|
/*
|
|
* Not configured:
|
|
* - TSI Slider on PTB16/TSI0_CH9 and PTB17/TSI_CH10
|
|
* - I2C inertial sensor on I2C0, routed to PTE25 and PTE25
|
|
* Note: these pins are assigned to I2C0 by default;
|
|
* if I2C0 is wanted on other pins, these need to be
|
|
* assigned another function explicitly!
|
|
*/
|
|
|
|
#if !defined(_FROM_ASM_)
|
|
#ifdef __cplusplus
|
|
extern "C" {
|
|
#endif
|
|
void boardInit(void);
|
|
#ifdef __cplusplus
|
|
}
|
|
#endif
|
|
#endif /* _FROM_ASM_ */
|
|
|
|
#endif /* _BOARD_H_ */
|